Saab 9-3

ISO to Din Antenna Aerial Adaptor, converts car specific antenna connector to a universal aftermarket connector.Aerial AdaptorAn Aerial Adaptor is needed when replacing the original factory fitted head unit with an aftermarket head unit. Antenna Adaptors are available in both ISO and DIN ver..

Package Includes:1 x Alpine 3-1/2" (8.6cm) Coaxial 2-Way SpeakerFeatures:Peak Power 150W RMS Power 20W Frequency Response: 120Hz-16kHz Sensitivity: 89dB/W/m Ferrite Magnet Long Fibre Natural Pulp Cone Alnico Magnet Piezo Tweeter High Polymer Foam EdgeDimensi..

This adaptor is required to replace factory fitted radio with an aftermarket headunit (Alpine, Pioneer, Kenwood, Sony, JVC etc.). It will convert the car original power and speakers wiring connector to a standard ISO connector. Simply plug one end of the adaptor into your cars wiring harness, and th..

This adaptor is required to replace factory fitted radio with an aftermarket headunit (Alpine, Pioneer, Kenwood, Sony, JVC etc.). It will convert the car original power and speakers wiring connector to a standard ISO connector. Simply plug one end of the adaptor into your cars wiring harness, and th..

These adaptors will convert the non din-sized aperture left after removing the factory stereo to a Double din size ready for head unit installation. The high quality finish, colour and texture are designed specifically to maintain the original look of your vehicles interior.Important Fascia Note..

Connects2 Steering Wheel Control Interface Adaptor. Connecting to the original radio connector and plugging in to the back of the new head unit is simple to fit.A stalk/steering wheel control adaptor allows you to upgrade to an aftermarket head unit whilst maintaining use of your factory steerin..

Complete stereo upgrade kit to install a Double DIN aftermarket radio and retain the use of the steering wheel controls in a SAAB 9-3 (2006-2013) vehicle, originally fitted with either the Delphi Grundig head unit or the Fujitsu Ten head unit.Package IncludesDouble Din Fascia Adaptor Do..

ISO to ISO Amplifier Integration Interface4 channel adjustable ISO to ISO amplifier interface.Use to install a new radio in a car that has an original fit amplifier that takes a pre amplified audio feed.This interface converts the high level audio output of a new head unit to a low level..

This adaptor is required to replace factory fitted radio with an aftermarket headunit (Alpine, Pioneer, Kenwood, Sony, JVC etc.). It will convert the car original power and speakers wiring connector to a standard ISO connector. Simply plug one end of the adaptor into your cars wiring harness, and th..

Connects2 T-Harness SOT Leads are primarily used when installing Parrot Bluetooth Car kits but can also be used to install other bluetooth devices and hands free kits into the car. SOT lead is designed to interface between the radio and the radio harness. It provides a power and earth supply to the ..

This adapter allows an aftermarket head unit to be installed, whilst bypassing the factory fitted amplified system. This adapter is designed to match the correct impedance of the vehicles speaker system.When connected your new stereo may not power up, and this is no fault of the wiring harness..

Car Audio Steering wheel control interface allowing use of the original buttons with a new aftermarket head-unit.Suitable for Saab 9-3/ 9-5 cars with GM LAN bus connectors behind the radio.This interface provides ignition, illumination, speed pulse, reverse gear signal for 9-3 models and Ign..

Car audio metal cage kit and trim 103mm high. Needed with some double din fascias that do not fit the normal 113mm cages supplied with aftermarket head-units.This kit is designed to replace the metal cage kit that is usually supplied with your new aftermarket double din head-unit or navigation s..

A pair of premium high-end BLAM 690RC (6 X 9 INCH) coaxial speakers.This system includes two 6"x9" woofers, with coaxial 25mm (1") soft dome tweeters and two integrated 6 dB/octave crossovers.The BLAM 690RC are designed to provide incredible performance. Because of their high ..

Car radio fascia adaptor panel to allow the fitting of an aftermarket single or double din car radio upgrade.The fascia adaptor allows the fitting of an aftermarket radio into the dashboard by matching the shape, style and colour of the original radio.Use the supplied pocket with the fascia ..

Car Audio Steering wheel interface and ISO cables allowing use of original buttons with a new aftermarket head-unit.This interface allows use of cars original steering wheel buttons with a new audio system or navigation unit.Suitable for: Saab 9-3 (1998-2003),  Saab 9-5 pre-facelift car..

A pair of front door car speaker adapter panels for 165mm speakers. MDF panels for to fit 165mm (6.5 Inch) speakers to the front doors of Saab 93 (2002-2012) car models.These panels allow you replace the cars original speakers with new improved quality aftermarket speakers.Technical Dat..

Saab AUX in cableSaab 93 / 95  2006 onwards Aux in cable to Phono plug  for  cars with AUX ready head-units. Suitable for Grundig and Fijutsu Ten standard head-units. NOT FOR SAT NAV Original head-unitsCONNECTOR HAS TWO ROWS OF 8 PINS (16 TOTAL)connect your iPhone, iPod or..

Connects2 T-Harness SOT Leads are primarily used when installing Parrot Bluetooth Car kits but can also be used to install other bluetooth devices and hands free kits into the car. SOT lead is designed to interface between the radio and the radio harness. It provides a power and earth supply to the ..

These adaptors will convert the non din-sized aperture left after removing the factory stereo to a Single din size ready for head unit installation. The high quality finish, colour and texture are designed specifically to maintain the original look of your vehicles interior.Car Audio Fitting A..